These might be the best off-road recovery straps you can buy. ARB makes some of the best products on the 4×4 market, including the well-known ARB Deflator and Inflator along with a handful of other products.  If you are looking for the best product out there, hands down this is going to be your best option. Because the ARB is made of 100% nylon means it has the most elasticity of these other brands.

By making this shackle hitch receiver out of drop forged steel, we’re able to get the most out of the mechanical properties of the steel. This is done by not compromising the grain direction of the steel, resulting in one of the strongest, most reliable products you’ll find on the market. While other brands are forging or machining their D-ring hitch for you, we’re relying on the time-tested drop-forging method. Not only is it the best method for making a shackle hitch receiver, but it sounds pretty rugged too.
Nylon Recovery Straps are great for situations where you may need to get a running start and traction all around is not so great. If you are in a situation where both you and the stuck driver are in sand, mud, snow or ice, you will need a running start to gain momentum. Once you have enough momentum and that point hits where the nylon recovery strap stretches out, the momentum should be enough to pop another vehicle out, all without a big JOLT of pull on both vehicles. The downside of nylon recovery straps is if used incorrectly and the nylon snaps, that stretch has to go somewhere. If a nylon strap stretches to hard and too fast, it will backlash at a vehicle or even worse a person’s face. Just make sure to keep vehicles and people clear of the recovery area when pulling someone out.
You can see the large opening space that we have here. I'll take a measurement of that here in a moment. On the shackle itself it's going to give you the diameter which again is 1-1/2" and then on this side it's going to say WLL, that's working load limit, of 17 tons. This is CNC machined when it comes to the solid steel mount. You can see here on the back side solid steel construction. It has a really nice nickel plating on it so it's going to stand up really well against rust and corrosion too. You're going to notice that it's going to have a 5/8" pin hole here on the side as well as here on the top.
How much weight your vehicle can handle while it is towing a car or trailer is perhaps the most important factor that people will look at when they are deciding what type of truck hitch to purchase. As briefly stated above, shackle hitches are the most affordable way to get a hitch that can handle weight over 10,000 pounds. Since this is more than the normal weight that people will drag around, many people with heavy-duty needs will get this design.
Use this heavy-duty, hitch-mounted shackle as an attachment point for strap, cable, or rope. Powder coated steel resists rust. Hitch pin and clip sold separately. Features: Tow ring lets you attach recovery strap, cable, or rope (sold separately) to be used in agricultural, industrial or recreational applications Hitch-mounted design ensures quick, simple
Today, we're going to be taking a look at part number BDW20239. This is the Bulldog Winch 3/4" Shackle for 1-1/4" Hitches. This is designed to fit most Class I and Class II receivers. Now, when it comes to the capacity, we're looking at a 3500-lb working load limit or your vehicle's receiver capacity, so you'll want to go by whichever is lower. This is going to be great for recovery situations. Simply provides an attachment point for recovery strap. This piece is going to be the piece that mounts inside your hitch.
Rhino Hitch products are both beautiful and strong, like our namesake animal. If you have been searching for the best custom adjustable hitch for your truck, then look no further! The Rhino Hitch is the most versatile, custom adjustable hitch on the market today and we proudly manufacture our custom hitches here in the USA. Our tow hitch is rated to pull up to 14,000 pounds of cargo. So, it really doesn’t matter if you’re hauling a boat for a day on the lake, a motor home for a trip to the dunes, or a trailer full of equipment for your job, because the adjustable Rhino Hitch will pull anything within the weight limit. More than that, we assure you that the hitches are sturdily built using high-quality billet aluminum. With few moving parts and fastened by industrial-strength bolts, your Rhino Hitch ensures a lifetime of heavy lifting.
By making this shackle hitch receiver out of drop forged steel, we’re able to get the most out of the mechanical properties of the steel. This is done by not compromising the grain direction of the steel, resulting in one of the strongest, most reliable products you’ll find on the market. While other brands are forging or machining their D-ring hitch for you, we’re relying on the time-tested drop-forging method. Not only is it the best method for making a shackle hitch receiver, but it sounds pretty rugged too.

With the Grip recovery strap mentioned above, it is a pretty stiff pull/ yank. With nylon, you are supposed to have a much softer yank. When you go from 0-20 and pull someone out, it tends to bounce everything around quite a bit. Then repeat this about 10 times in a day. Yeah, we have been there. The softer and easier you can get those pulls, the easier it is on everything, your back, your 4Runner, and the driver of the other truck.
It seems that the negative reviews about size variations are from a few years ago, and based on the one I received, they seem to have the size right. The main block on mine (drawbar?) measures 1.90 inches wide and 1.97 inches tall. My 4Runner hitch measures 2.08 inches wide and tall, so there is about 1/8" of extra space between the receiver and the drawbar. Without a pin, there is quite a bit of play, but with the pin inserted, it's pretty snug.
You can see the large opening space that we have here. I'll take a measurement of that here in a moment. On the shackle itself it's going to give you the diameter which again is 1-1/2" and then on this side it's going to say WLL, that's working load limit, of 17 tons. This is CNC machined when it comes to the solid steel mount. You can see here on the back side solid steel construction. It has a really nice nickel plating on it so it's going to stand up really well against rust and corrosion too. You're going to notice that it's going to have a 5/8" pin hole here on the side as well as here on the top.
Affordable and efficient strap-and-shackle system attaches to your Rhino-Rack Heavy-Duty crossbar to secure a ladder or other cargo to your roof rack. Cam-action buckle locks the strap in place; a snap-on shackle anchors the strap to your crossbar. Call 800-298-8924 to order Rhino Rack accessories and parts part number RLS5 or order online at etrailer.com. Free expert support on all Rhino Rack products. Guaranteed Lowest Price and Fastest Shipping for Cam-Lock Ladder Strap with Snap Shackle for Rhino-Rack Heavy-Duty Crossbars - 20" Long. Accessories and Parts reviews from real customers.
I think it would be fine for a lite recovery, I've had to use that method winching a guy out of a snow bank(he had no recovery points). I don't see how much more different it is than using a receiver slug set up with a shackle. But I guess it depends on the quality of the pin. I too have seen it demonstrated as what to do instead of using the ball.
Icon ext. travel 2.5RR in front, Icon ext. travel 2.0RR in rear, BuiltRight uniball UCAs, Wheelers Superbumps, Goodridge steel braided brake lines, BruteForce front plate bumper w/ Warn M9000+synth line, 255/75R16s on painted stockers...because I'm not paying $800 to rock rash new wheels you scrubs. Shok Industries 2/0 big 4 upgrade and sound deadener.
Today we're going to be taking a look at part number BDW20181. This is the Bulldog Big Dog Shackle. This is the huge oversize shackle that's going to give that truck a nice, big truck look. This portion right here is going to slide into your 2" by 2" trailer hitch receiver. It's going to be great for work trucks that use very large straps. It's going to feature an 1-1/2" diameter forged alloy steel shackle. It has a really nice zinc plating on it so it is going to stand up really well against rust and corrosion.

Polyester Recovery Straps stretch about 2% so they are pretty stiff. With Polyester recovery straps you have more of a stable, controlled yank when pulling someone’s truck out. With polyester recovery straps, you have a solid pull from the start but you don’t want to have a very large gap and delay in the pull. With polyester straps, you want short jerks or short pulls, not long driving starts. Polyester recovery straps are great for a quick pull if you are on stable ground and someone else is stuck and the distance is relatively close.
I think it would be fine for a lite recovery, I've had to use that method winching a guy out of a snow bank(he had no recovery points). I don't see how much more different it is than using a receiver slug set up with a shackle. But I guess it depends on the quality of the pin. I too have seen it demonstrated as what to do instead of using the ball.
Use this heavy-duty, hitch-mounted shackle as an attachment point for strap, cable, or rope. Powder coated steel resists rust. Hitch pin and clip sold separately. Features: Tow ring lets you attach recovery strap, cable, or rope (sold separately) to be used in agricultural, industrial or recreational applications Hitch-mounted design ensures quick, simple

This hitch works by mounting it directly to the frame of the vehicle behind you, allowing the two vehicles to work almost as if they were one. However, keep in mind that you should not tow heavy-duty weights or vehicles with this vehicle. Since there is not a clear weight capacity with this hitch, it is best used for loads that are lighter than the vehicle you already use.
A Class 1 or Class 2 receiver has a 1-1/4” opening and is typically only used on cars for towing small trailers or supporting a bike rack. Class 3 and Class 4 receivers have a 2” opening. You'll find these on larger SUV's (the body-on-frame type, not crossovers,) and pickup trucks. A Class 3 receiver can handle up to 6,000 lbs (depending on design,) while a Class 4 can go up to 10,000 lbs. (Again, that's design-dependent.)
×