Love this receiver, gives you another attachment point that you can count on. This is my main recovery point, and whenever I am in the trails I already have this attached with a D ring to my recovery strap. I used multiple times and is one of the strongest points to attach to. This also gives you the option to hook up just when you need it, and if you have other vehicles with a class 3 hitch you can transfer to any of them. This is a must if if have vehicles or equipment that could get stuck. No only that, but this is a fraction of the cost of purchasing a custom bumper with recovery attachment points.
Solid, heavy, very thick coating. Look like they will hold up as advertized although I haven't had a chance to use them yet. Fit and finish is at least as good as higher-priced shackles I've seen at my local S&M Bondage store and I think they'll go well with that early 20th century farmhouse basement steam radiator theme or in any safe house as well. Finding chain and manacles to match might be a chore, but look around.
Nice looking piece, what you would expect from a simple shackle hitch reciever. Shackle itself also a nice piece... down fall is the extremely loose fit in a 2" reciever. Planned on running this full time as a front recovery point in my Trail Gear tube bumper but it rattles and clanks around over any sort of bumps. Ended up purchasing a different shackle hitch reciever for less here on amazon that came with shackle, hitch pin, shackle, polyurethane shackle isolators and it fit nice and snug. If the fit was better I would have been happy with this purchase. Ended up needing to use it and scuffed the finish otherwise I would have returned it.
You can see the large opening space that we have here. I'll take a measurement of that here in a moment. On the shackle itself it's going to give you the diameter which again is 1-1/2" and then on this side it's going to say WLL, that's working load limit, of 17 tons. This is CNC machined when it comes to the solid steel mount. You can see here on the back side solid steel construction. It has a really nice nickel plating on it so it's going to stand up really well against rust and corrosion too. You're going to notice that it's going to have a 5/8" pin hole here on the side as well as here on the top.

Today, we're going to be taking a look at part number BDW20239. This is the Bulldog Winch 3/4" Shackle for 1-1/4" Hitches. This is designed to fit most Class I and Class II receivers.	Now, when it comes to the capacity, we're looking at a 3500-lb working load limit or your vehicle's receiver capacity, so you'll want to go by whichever is lower. This is going to be great for recovery situations. Simply provides an attachment point for recovery strap. This piece is going to be the piece that mounts inside your hitch.

Also the bolt through a hitch receiver is in double shear, so unless you are driving a M35 and pulling out an M1A1 it's unlikely that you will stress a hitch pin or bolt to failure yanking out Hiluxes and Wranglers. The only disadvantage IMO to using the loop-and-pin method is convenience, stuffing the strap in can be a pain and sharp edges do need to be smoothed to keep abrasion minimized. But it's a perfectly legitimate and safe way to connect to a recovery point and does eliminate additional connections, which is good.
24x48 Outside dimensions. Hitch-mounted cargo carrier with lockable lid offers 13 cu ft of storage space, and it folds flat and tilts up against your vehicle when not in use. Walls provide vertical to the rear of your vehicle Lockable lid minimizes the need for cargo nets or tie-down straps Deters theft when used with a padlock (sold separately) with a 3/8" diameter shackle Mounts to Carpod sidewalls
Use your Roadmaster tow bar to tow your off-road vehicle behind your motor home with these adapter brackets. They attach to the 1" thick shackle mounts on your bumper where the D-rings Features: Adapter brackets let you use your Roadmaster tow bar to tow your off-road vehicle with bumper-mounted D-rings Brackets attach to 1" thick shackle mounts on bumpers approved for flat

Love the Bulldog winch 3/4" ×1-1/4 shackle. Its very strong, works & looks great, on my Scrambler 1K. I've had the bulldog for over a year now and it has not let me down. I had a difificult time finding a shackle of this size and quality here in Canada. Until I came across etailer.com. I would definitely recommend this shackle for any atv/utv with a 1-1/4 hitch. I need to get 2 more for the RzR & Ace and for me it's a no brainer where I'll be ordering again from etrailer.com made easy. Thanks 547879


Solid, heavy, very thick coating. Look like they will hold up as advertized although I haven't had a chance to use them yet. Fit and finish is at least as good as higher-priced shackles I've seen at my local S&M Bondage store and I think they'll go well with that early 20th century farmhouse basement steam radiator theme or in any safe house as well. Finding chain and manacles to match might be a chore, but look around.
×