Assume the whole bar is well attached to the frame rails at each side (otherwise, it's definitely not good for a snatch recovery!). There is a huge difference between pulling on the receiver mount in the middle of the cross-bar, and pulling with a long harness attached to both ends. The direct receiver-mount pull will tend to bend the cross bar outwards, and pull the frame rails in towards each other (with a lot of leverage, on top of the many tons of force imparted by a snatch recovery).
2011 SR5 4x4, Magnuson Supercharger, ICON ET coil overs, MT ICON LT rear, MT offset lower links, URD Y-Pipe, TC UCAs, Baja Rack, MT Sliders, RCI Aluminum skids, 4.56 gearing with ARB lockers front and rear. 305/70 Goodyear MTRs (34") on Konig Countersteer 17x8. Addicted front bumper, Custom undercover tube protection rear. LT font or SAS going on next.

A Class 1 or Class 2 receiver has a 1-1/4” opening and is typically only used on cars for towing small trailers or supporting a bike rack. Class 3 and Class 4 receivers have a 2” opening. You'll find these on larger SUV's (the body-on-frame type, not crossovers,) and pickup trucks. A Class 3 receiver can handle up to 6,000 lbs (depending on design,) while a Class 4 can go up to 10,000 lbs. (Again, that's design-dependent.)
There are plenty of great parts to choose from when you buy from 4wheelparts.com. You find recovery hitches from a wide range of brands, including Warn, Rugged Ridge and Factor 55. To get a sense of which hitches work best for your Jeep, you simply need to input the pertinent information into 4 Wheel Parts.com's search bar to automatically see the results.
With that being said though, it all depends on how you plan to use your 4Runner off-road and the types of terrain you see. Because the ARB Off-Road Recovery Snatch Straps have the most stretch, doesn’t mean they are the “best” it just means that they are truly designed for off-road recovery in pulling someone out. Again, like we said above in the material section, there are different recovery straps that perform better in certain situations.

Use your Roadmaster tow bar to tow your off-road vehicle behind your motor home with these adapter brackets. They attach to the 1" thick shackle mounts on your bumper where the D-rings Features: Adapter brackets let you use your Roadmaster tow bar to tow your off-road vehicle with bumper-mounted D-rings Brackets attach to 1" thick shackle mounts on bumpers approved for flat


That's going to allow for easy and quick connect and disconnect of the recovery strap . Now, this is going to be great for ATVs and UTVs that have an 1-1/4" hitch on it. It is going to require a 1/2" hitch pin and clip or lock to get it secured into the hitch. That item is sold separately. You can find those right here at etrailer.com. A few measurements to go over with you real quick.
Replace your vehicle's rear bumper with this sturdy steel recovery bumper. The integrated, swing-away spare tire carrier can hold up to a 37" tire. Welded shackle mounts come with D-rings shackle mounts with removable D-rings let you perform recovery operations Integrated receptacles let you add 2 auxiliary can lights (sold separately) up to 4" in diameter Ground-level lighting allows
I honestly didn't have too high of expectations when purchasing this product as the cost was a lot easier on the wallet than local farm supply stores. That being said, this thing has a beautiful fit and finish. The ability to have the shackle mounted sideways, keeps from damaging your rope from pinch points. This thing is a solid chunk of steel. I'm not entirely sure that it is possible to damage this hitch on a full size truck. The hitch pin or shackle will fail way before the receiver will. Make sure you use this thing as it is intended because if you manage to rip this off, it is going to take armor plating to stop this thing in a projectile state. It is SOLID! Also, buy a locking hitch pin. Someone would definitely steal this if they have the chance.
×