14-1/2" x 17-1/2" Weatherproof cover slips easily over your electric tongue jack and secures with drawstring. Helps to protect jack motor from the elements. Fits Ultra-Fab Odyssey and most Features: Weatherproof cover protects your electric jack from dirt, grime, and inclement weather when not in use Slips over top of jack to cover motor assembly, switch and/or light Drawstring runs
Application: for use on heavy duty trucks, semi trailers, cargo trailers, boat trailers, work vehicles and a wide or narrow overland vehicle requiring quality DOT rated lighting. Product Features: Brand new, waterproof, Super bright Red LED Surface Mount, sealed 15" light Each light has 11 Super Diodes for a Bright Performance. Functions as clearance, side marker or identification light, stop, turn, tail and brake light These light bars have 3 wires for ground, brake, turn and tail light.(White is ground,Black is running lights,Red is turn and brake.) They have 2 screw holes for mounting Comes with a Polycarbonate Lens with All Weather Housing for durability Convert your old incandescent lights to more modern LEDs. Dimensions: 15.5" x 1.25" x 0.5" Hole Center to Center is 14-1/2".
It sounds like the Bulldog A-Frame Jack, part # BD500200 is just what you are looking for. The BD500200 has an outer tube diameter of 2-1/4 inches which matches what you are replacing and this jack has 2 toggle switches. One is used to control the up and down movement of the jack and the other switch turns the LED lights on and off. The mounting plate features mounting holes that allow you to mount it so the controls are at the front of the jack or mount it so that the controls are...
There are several places water can get into any given jack. Water should be able to drain out though. If the exit points which would be at the lowest point are clogged then the water would not be able to exit. You could use a jack cover like # UF38-944020 for future use. There is no telling how much damage is really done. If there is enough corrosion then something inside could be structurally compromised and fail when you have weight on the jack. I would not be comfortable offering...
14-1/2" x 17-1/2" Weatherproof cover slips easily over your electric tongue jack and secures with drawstring. Helps to protect jack motor from the elements. Fits Ultra-Fab Odyssey and most Features: Weatherproof cover protects your electric jack from dirt, grime, and inclement weather when not in use Slips over top of jack to cover motor assembly, switch and/or light Drawstring runs
This custom-fit mount lets you secure your Hi-Lift jack to the driver's side of your Jeep. The jack mount lock codes to your ignition key. Automotive-grade, weather-resistant black powder coated of keys - for your hitch lock and coupler lock, your pickup cover or trailer door, and all the various padlocks securing your equipment? Tired of fumbling for the right key or having to replace a lost key?
Please inspect the packaging of your item(s) when they arrive, if you notice any damage you should make note of it on the delivery date. If your item(s) do arrived damaged, please send photos to sales@rvcoversupply.com and we will process an insurance claim on your behalf. When installing your cover Please be sure the unit is clean and sharp objects are covered accordingly when to prevent any damage. A dirty, ripped, scratched or torn cover cannot be returned for a refund. Manufacturers warranty information can be found by clicking the "Featured Manufacturers" tab at the top of our homepage. A warranty may be void if the product has been damaged by accident, misuse, abuse, or other abuses not arising out of defects in material or workmanship and does not cover everyday wear and tear.
I can help you find a cover for your Fulton F2 Hand Winch # FW32000101. I was able to go out to our warehouse and try the Ultra-Fab Cover # UF38-944020 on the Fulton winch # FW32000101. This bag measures 12 by 14-1/2 inches. I have linked a few pictures to see how it fit. The bag was able to stretch over the housing unit but not the handle when attached. We also have a 14-1/2 by 15-1/2 vinyl bag # UF38-944026, that will give you slightly looser fit than the one pictured. Since...

So every time she has had to hitch up, which is often, raising  and lowering her jack has darn near thrown her back back out. To make matters worse, with an e2 weight distribution hitch she loathes, she has to (usually) RAISE the jack up to get the coupler high enough to clear the ball, LOWER it down onto the ball. Then she has to again RAISE the hitch way up, literally lifting the back of the truck, so she can get her weight distribution bars high enough to install them. Finally, she has to LOWER it back down until the jack foot is all the way up. That's a lot of cranking and it makes Kelly cranky. (Sorry. Couldn't resist.)
10-1/2" x 13-3/4" Weatherproof cover slips easily over your electric tongue jack and secures with drawstring. Helps to protect jack motor from the elements. Fits most brands and styles of electric A-frame jacks. Call 800-298-8924 to order Ultra-Fab Products accessories and parts part number UF38-944020 or order online at etrailer.com. Free expert support on all Ultra-Fab Products products. Guaranteed Lowest Price and Fastest Shipping for Ultra-Fab Protective Cover for Electric A-Frame Jacks - Vinyl - 10-1/2" x 13-3/4". Accessories and Parts reviews from real customers.

Law enforcement agencies generally support the Taser as a worthy tool that protects officers from violent offenders and protects the suspects as well. According to Taser International, founded in 1993, which markets products based on Mr. Cover’s original invention, more than 13,400 law enforcement agencies around the world now use Tasers. More than 375,000 individual officers have them, and so do more than 181,000 private citizens.
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring. Powered converter reduces strain on wiring system. cargo area on the driver's side and passenger's side. You will have to remove the jack storage cover and some interior paneling to access this harness. Once you've plugged in the connector,
It sounds like the Bulldog A-Frame Jack, part # BD500200 is just what you are looking for. The BD500200 has an outer tube diameter of 2-1/4 inches which matches what you are replacing and this jack has 2 toggle switches. One is used to control the up and down movement of the jack and the other switch turns the LED lights on and off. The mounting plate features mounting holes that allow you to mount it so the controls are at the front of the jack or mount it so that the controls are...
I have used this cover to cover the tow jack on my trailer which has been parked up on the drive of my beach house for the last 12+ months. It has therefore been subjected to a marine type environment which plays havoc with house door fittings etc. The cover has survived intact and is now still in an "as new" condition. I am very pleased with this purchase and highly recommend it. 424779
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-One connector plugs directly into OEM tow package wiring harness - no cutting or splicing required. Features: Provides a 4-way flat trailer connector at the back of your vehicle to power your trailer's signal lights Designed for use with a factory tow package Compatible with 5-pole, 6-pole
×